Best selling

Best selling19 Products

Category
  • Accessories&Tools (17)
  • Best selling (19)
  • Epever MPPT Controller (20)
  • Feature Products (12)
  • Gird tie inverter (16)
  • Inverter (27)
  • Inverter/Charger (7)
  • MC4 Connectors (7)
  • MC4 Connectors (2)
  • MPPT Solar Charger Controller (12)
  • Off tie inverter (2)
  • PWM Solar Charger Controller (1)
  • Tool (0)
  • US warehouse (0)
  • USA Warehouse (24)
  • Waterproof Grid tie inverter (5)
-23%
$168.99 $220.00

User's Manual 

 

 

Product Description

Prolong The Life Of Your Battery!

The smart battery protection system shields your device from getting over charged, over load, discharge, over heated, reverses polarity and also provides efficient short circuit protection. It can handle 520W Solar Panel on 12v battery system or 1040W Solar Panel on 24v battery system. Works equally great for home, industrial or commercial use. Designed for optimum and safe charging performance.

Technical Data

40A MPPT Charge Controller Nominal System Voltage: 12V, 24V

Rated Charge Current: 40A

Rated Load Current: 20A

Max PV Open Circuit Voltage: 150V / 138V

Max PV Input Power: 520W (12v battery) / 1040W (24v battery)

MT50 Remote Meter Faceplate dimension:98×98 mm / 3.86×3.86 inch Frame dimension:114×114 mm / 4.49×4.49 inch Connector type: RJ45 Meter cable:Standard 2m,Max 50m Ambient Temperature: -20°C -- +70°C/-4°F -- 158°F

Remote Temperature Sensor Acquisition of battery temperature for undertaking temperature compensation of control parameters Length: 3 M

USB to RS485 Converter Adapter This adapter is used to monitor each controller on the network using Solar Station PC software and update the firmware.

Tracer 4215BN Series MPPT Solar Charge Controller 150V PV

MPPT Solar Charge Controller 40A Tracer4215BN Schematic Diagram

EPEVER MPPT Solar Charge Controller 40A 150V PV input Negative Ground Schematic Diagram

 

GO   VIDEO DEMO

 Latest product information(For more product video please click here 

 

    -16%
    $201.99 $240.00

    User's Manual


    Product Description

    MPPT Solar Charge Controller 100A EPEVER Tracer 10420AN

    Based on common negative design and advanced MPPT control algorithm

    MPPT Charge efficiency > 99%

    Technical Data: Nominal system voltage:12/24/36/48VDC auto work

    Rated charge current :100A

    Battery input voltage range: 8-68V

    Max. PV open circuit voltage:200V(at minimum operating environment temperature) 180V(at 25℃ environment temperature)

    MPP voltage range:V(BAT)+2V~144V

    Max. PV input power: 1250W/12V battery, 2500W/24V battery , 3750W/36V battery, 5000W/48V battery system

    Max Wire Size: #2 AWG(35mm2)

    Recommended Wire Size: #2 AWG(35mm2)

    Weight: 7.4kg

    MT50 Remote Meter

    This unit is compatible with Tracer A(N) , TRIRON N, Tracer BN, VSxxxxBN series controllers ONLY from EPsolar. And it's NOT compatible with RN series MPPT charge controller. Description MT-50, a new-generation remote display for EPEVER MPPT controllers is an associated display device which supports both the latest communication protocol and the voltage technology standard of mppt solar controllers.

    Technical Data Faceplate dimension:98×98 mm / 3.86×3.86 inch Frame dimension:114×114 mm / 4.49×4.49 inch Connector type: RJ45 Meter cable:Standard 2m,Max 50m Ambient Temperature: -20°C -- +70°C/-4°F -- 158°F

    80A MPPT Solar Charge Controller Tracer8420AN

     

    EPEVER Tracer AN series mppt solar charge controller (100A)

    Based on multiphase synchronous rectification technology (MSRT) and advanced MPPT control algorithm, with dual-core processor architecture and common negative design, has the features of high response speed, high reliability, and high industrial standard.

    MSRT can give a very high conversion efficiency in any charge power, which sharply improves the energy efficiency of solar system;

    Advanced MPPT control algorithm minimize the maximum power point loss rate and loss time, to ensure the tracking efficiency, corresponding speed as well as high conversion efficiency under high or low power, so that in any situation, Tracer AN products can rapidly track the maximum power point(MPP) of PV array to obtain the maximum energy of the panel.

    The limitation function of the charging power and current, and automatic power reduction function fully ensure the stability when works with oversize PV modules and operate under high temperature environment.

     

     

    GO   VIDEO DEMO

     Latest product information(For more product video please click here 

     

     

      -7%
      $129.99 $140.00

      User's Manual


      Product Description

      40A EPEVER Tracer 4210AN MPPT Solar Charge Controller

      Based on common negative design and advanced MPPT control algorithm

      MPPT Charge efficiency > 99%

       

      Technical Data: Nominal system voltage:12/24VDC auto work

      Rated charge current :40A

      Rated discharge current: 40A

      Battery input voltage range: 8-32V

      Max. PV open circuit voltage:100V(at minimum operating environment temperature) 92V(at 25℃ environment temperature)

      MPP voltage range:V(BAT)+2V~72V

      Max. PV input power:520W(12V Battery) & 1040W(24V battery)

      Power terminals:#6 AWG(16mm2)

       

      MT50 Remote Meter

      This unit is compatible with Tracer A(N) , TRIRON N, Tracer BN, VSxxxxBN series controllers ONLY from EPsolar. And it's NOT compatible with RN series MPPT charge controller. Description MT-50, a new-generation remote display for EPEVER MPPT controllers is an associated display device which supports both the latest communication protocol and the voltage technology standard of mppt solar controllers.

      Technical Data Faceplate dimension:98×98 mm / 3.86×3.86 inch Frame dimension:114×114 mm / 4.49×4.49 inch Connector type: RJ45 Meter cable:Standard 2m,Max 50m Ambient Temperature: -20°C -- +70°C/-4°F -- 158°F

      Something you should know for Lithium Batteries Charging

       

      1. When a lithium-ion battery is used, the system voltage cannot be identified automatically, please confirm the battery system voltage before installation.
      2. When you choose lithium battery as a battery type, the temperature compensate coefficient would be 0, and cannot be changed.
      3. This MPPT solar charge controller can work under full load in the ambient temperature range. when the internal temperature reach 81℃, the power reduction mode will be turned on.
      4. Lithium battery type can ONLY be set on a cellphone app or "solar station monitor" PC software.

       

       

      Schematic Diagram

       


       


      Warm tips:

      Step: Connect the system in the order of 1.battery-->2. load-->3.PV array, and disconnect the system in the reverse order 3. 2. 1.

      • NEVER connect the soalr panel array to the controller Without/Before a Battery.
      • Battery must be connected FIRST !!!
      • DO NOT connect any inverter/ wind/Alternator or Charger into the charge controller!
      • If the remote temperature sensor is not connected to the controller,, the default setting for battery charging or discharging temperature is 25 °C without temperature compensation.
      • The wire size is only for reference. If there is a long distance between the PV array and the controller or between the controller and the battery, larger wires can be used to reduce the voltage drop and improve performance. 

       

      How to program for Lithium Battery?


      1. Via PC (Accessories needed:RS485),
      2. Via phone APP (Accessories needed:Ebox-Wifi or Ebox-Blue)
      Software download website: EPever official website or look for in the manual

       

      GO   VIDEO DEMO

       Latest product information(For more product video please click here 

       

        -25%
        $15.00 $20.00
        Description

        This adapter is used to monitor each controller on the network using

        Solar Station PC software and update the firmware.
        this item include the two cables. 
        1. Remote Temperature Sensor 
        Model: RTS300R47K3.81A 
        Acquisition of battery temperature for undertaking 
        temperature compensation of control parameters 
        Length: 3 M 

        2. USB to RS485 Converter Adapter 
        Model: CC-USB-RS485-150U 

         

          Quick look
          -16%
          $158.99 $189.00
          • 【High PV Input Power】This 60 amp MPPT Solar Panel Charger works with 840W Solar Panel on 12V Battery System and 1680W on 24V Battery.
          • 【Compatible with a variety of batteries】Negative grounding design, four load control modes, supports lead-acid and lithium batteries.
          • 【Powerful electronic protections】Eight electronic protections, including reverse polarity protection(for battery and array), solar short circuit protection, over-temperature protection, load short circuit protection, load over-current protection, heat sink temperature limit protection, over-volt / low-volt protection and battery shedding protection.
          • 【OLED screen and MH-M80 Meter】The controller has a 1.3 inches OLED screen and a function button. MH-M80 Meter was attached, which can display system operating information and error indications. In addition to that, 3 status LEDs provide system status at a glance. The meter can easily set the parameters of the controller.
          • 【4-stage battery charging】4-stage battery charging algorithm for rapid, efficient, and safe battery charging. The maximal wire size of the controller is 3AWG(25mm2).

           


          Product Description

          Technical Data

          60A 150V MPPT Solar Charge Controller Nominal System Voltage: 12V, 24V

          Rated Charge Current: 60A

          Rated Load Current: 30A

          Max. PV Open Circuit Voltage: 150V

          Max. PV Input Power: 840W (12V battery) / 1680W (24V battery)

          Max. Wire Size: 25mm2 / 3AWG

          1

          Data & Communications

          Communication Port Dual RJ45
          Communication Protocols Private protocol and MODBUS
          PC Software SolarMate
          Meter MH-M80 / MH-S80
          Dry Contact Via RJ45 port
          2

           

          1. Charging status / Load output status / Error LED
          2. Function button
          3. Digital OLED display
          4. Temperature sensor terminals
          5. Dual RJ45 serial communication ports
          6. Input and output terminals (PV+/PV-/BAT+/BAT-/LOAD+/LOAD-)
          7. Dedicated for grounding wire
          8. Reverse fixing hole
          9. Mounting holes for positively fixed fittings
          10. Terminal cover plate

           

           

           

            Quick look
            -46%
            $74.99 $139.99

            EPEVER MPPT Solar Charge Controller 40 Ampere Tracer 4215BN

            Prolong The Life Of Your Battery by using this 40A MPPT Charger

            The smart battery protection system shields your device from getting over charged, over load, discharge, over heated, reverses polarity and also provides efficient short circuit protection.

            It can handle 520W Solar Panel on 12v battery system or 1040W Solar Panel on 24v battery system. Works equally great for home, industrial or commercial use. Designed for optimum and safe charging performance.

            Technical Data

            40A MPPT Charge Controller Nominal System Voltage: 12V, 24V

            Rated Charge Current: 40A

            Rated Load Current: 20A

            Max PV Open Circuit Voltage: 150V / 138V

            Max PV Input Power: 520W (12v battery) / 1040W (24v battery)

            Recommended Power Input: 600W (12v battery) / 1200W (24v battery)

            Recommended value for LiFePO4 batteries (12.8V / 4 cells in series)

            Boost Duration 120 sec.

            Temp. Compensation Coefficient:0

            Over Volt. Disconnect (V): 15.6V

            Over Volt. Reconnect (V): 14.7V

            Equalize Charging Volt. (V): N/A

            Boost Charging Volt.(V): 14.5V

            Boost Reconnect Charge Volt.(V): 13.2V

            Charging Limit Voltage (V): 14.6V

            Discharging Limit Volt. (V):10.6V

            Low Voltage Disconnect Volt. (V): 11.1

            Low Voltage Reconnect Volt. (V): 12.8

            Under Vol. Warning Volt.(V):12.0

            Under Voltage Warning Reconnect Volt. (V): 12.8

            MPPT Solar Charge Controller SolarEpic EPEVER Tracer 4215BN 150V PV Negative Ground

             

             

             

             

            GO   VIDEO DEMO

             Latest product information(For more product video please click here 

              -29%
              $20.00 $27.99

              Feature:

              Compatible with PC software & MT50 for real-time monitoring
              Connect to PC via USB interfaces with high compatibility
              Powered up by controller communication interface
              Record capacity: 20000 points(MAX)
              LED Indicator design, more intuitive display

              technical parameter

              Model

              eLOG01

              Input voltage

              410VDC

              Powered up by RS485 interface

              Average power consumption

              0.3W

              Baud rate

              115200

              Communication

              RS485

              Interface type

              2 RJ45

              1 Micro USB

              Record time

              10 minutes

              Dimensions

              71×67.62×25.8mm

              Mounting dimension

              57.6mm

              Mounting hole size

              Φ4.5

              Working temperature

              -2575

              Humidity

              5-95% (N.C.)

              Enclosure

              IP30

              Net weight

              42g

              Warranty

              2 years

               

                Quick look
                Out of stock

                 

                APK Download:Epever(WIFI&BLE)

                Feature:

                     eBox-BLE-01
                • Realize wireless monitoring function of solar controller and inverter
                • Support mobile phone APP, plug and play, simple and convenient to set
                • Use high performance, ultra-low power consumption Bluetooth dedicated chip
                • Adopt Bluetooth 4.0 and BLE technology
                • Fast communication, strong anti-interference ability
                • No need of external power supply
                • Communication distance up to 10 m
                • Master reset adapter

                Bluetooth

                    eBox-WIFI-01

                •  Realize wireless monitoring function of solar controller and inverter
                • Support mobile phone APP, plug and play, simple and convenient to set
                • Use high performance CPU with core M4
                • Ultra-low power consumption and high speed data processing capability
                • No need of external power supply
                • Communication distance up to 50 m
                • One-key restore the factory settings

                WIFI

                 

                Technical Specifications

                Model→

                Item↓

                eBox-BLE-01

                eBox-WIFI-01

                Input Voltage

                5VDC

                (Direct powered by RS485 port )

                5VDC

                (Direct powered by RS485 port )

                Standby power

                Consumption

                0.04W

                0.20W

                Operation power

                consumption

                0.05W

                0.25W

                Communication distance

                ≤10m

                ≤50m

                Port baud rate

                300bps~230400bps (Default115200)

                300bps~230400bps (Default 115200)

                Communication

                RS485 to BLE

                RS485 to WIFI

                Interface type

                RJ45

                RJ45

                Connecting cable

                Standard network cable

                (Parallel cable)

                Standard network cable

                (Parallel cable)

                Overall dimension

                51*67*24.5mm

                51*67*24.5mm

                Mounting dimension

                41.2mm

                41.2mm

                Mounting hole size

                Φ3.2mm

                Φ3.2mm

                Working temperatur

                -20~70℃

                -35~75℃

                Enclosure

                IP30

                IP30

                Net weight

                37g

                39g

                 

                  Search

                  Just added to your cart:
                  Qty:
                  Total:
                  Subtotal:
                  Excl. postage 
                  My Bag
                  Just added to your wishlist:
                  Excl. postage 
                  My Wishlist

                  Join Our Mailing List

                  Spin to win Spinner icon