LCD display,remote meter

Optional remote meter to our gird tie inverter

Automatic identify the inverter, and display relevant parameter data and system working status

Screen data : ac voltage,current and frequency,generating capacity,power factor

Have EU,AU,US,UK plug,choose the one as you want,thanks.

Description

User's Manual

Product Description

40A EPEVER Tracer 4210AN MPPT Solar Charge Controller

Based on common negative design and advanced MPPT control algorithm

MPPT Charge efficiency > 99%

 

Technical Data: Nominal system voltage:12/24VDC auto work

Rated charge current :40A

Rated discharge current: 40A

Battery input voltage range: 8-32V

Max. PV open circuit voltage:100V(at minimum operating environment temperature) 92V(at 25℃ environment temperature)

MPP voltage range:V(BAT)+2V～72V

Max. PV input power:520W(12V Battery) & 1040W(24V battery)

Power terminals:#6 AWG(16mm2)

 

MT50 Remote Meter

This unit is compatible with Tracer A(N) , TRIRON N, Tracer BN, VSxxxxBN series controllers ONLY from EPsolar. And it's NOT compatible with RN series MPPT charge controller. Description MT-50, a new-generation remote display for EPEVER MPPT controllers is an associated display device which supports both the latest communication protocol and the voltage technology standard of mppt solar controllers.

Technical Data Faceplate dimension:98×98 mm / 3.86×3.86 inch Frame dimension:114×114 mm / 4.49×4.49 inch Connector type: RJ45 Meter cable:Standard 2m,Max 50m Ambient Temperature: -20°C -- +70°C/-4°F -- 158°F

Something you should know for Lithium Batteries Charging

1. When a lithium-ion battery is used, the system voltage cannot be identified automatically, please confirm the battery system voltage before installation.
2. When you choose lithium battery as a battery type, the temperature compensate coefficient would be 0, and cannot be changed.
3. This MPPT solar charge controller can work under full load in the ambient temperature range. when the internal temperature reach 81℃, the power reduction mode will be turned on.
4. Lithium battery type can ONLY be set on a cellphone app or "solar station monitor" PC software.

Schematic Diagram

Warm tips：

Step: Connect the system in the order of 1.battery-->2. load-->3.PV array, and disconnect the system in the reverse order 3. 2. 1.

• NEVER connect the soalr panel array to the controller Without/Before a Battery.
• Battery must be connected FIRST !!!
• DO NOT connect any inverter/ wind/Alternator or Charger into the charge controller!
• If the remote temperature sensor is not connected to the controller,, the default setting for battery charging or discharging temperature is 25 °C without temperature compensation.
• The wire size is only for reference. If there is a long distance between the PV array and the controller or between the controller and the battery, larger wires can be used to reduce the voltage drop and improve performance. 

How to program for Lithium Battery？

1. Via PC (Accessories needed：RS485),
2. Via phone APP (Accessories needed：Ebox-Wifi or Ebox-Blue)
Software download website: EPever official website or look for in the manual

   VIDEO DEMO

 Latest product information（For more product video please click here） 

User's Manual

Product Description

MPPT Solar Charge Controller 100A EPEVER Tracer 10420AN

Based on common negative design and advanced MPPT control algorithm

MPPT Charge efficiency > 99%

Technical Data: Nominal system voltage:12/24/36/48VDC auto work

Rated charge current :100A

Battery input voltage range: 8-68V

Max. PV open circuit voltage:200V(at minimum operating environment temperature) 180V(at 25℃ environment temperature)

MPP voltage range:V(BAT)+2V～144V

Max. PV input power: 1250W/12V battery, 2500W/24V battery , 3750W/36V battery, 5000W/48V battery system

Max Wire Size: #2 AWG(35mm2)

Recommended Wire Size: #2 AWG(35mm2)

Weight: 7.4kg

MT50 Remote Meter

This unit is compatible with Tracer A(N) , TRIRON N, Tracer BN, VSxxxxBN series controllers ONLY from EPsolar. And it's NOT compatible with RN series MPPT charge controller. Description MT-50, a new-generation remote display for EPEVER MPPT controllers is an associated display device which supports both the latest communication protocol and the voltage technology standard of mppt solar controllers.

Technical Data Faceplate dimension:98×98 mm / 3.86×3.86 inch Frame dimension:114×114 mm / 4.49×4.49 inch Connector type: RJ45 Meter cable:Standard 2m,Max 50m Ambient Temperature: -20°C -- +70°C/-4°F -- 158°F

 

EPEVER Tracer AN series mppt solar charge controller (100A)

Based on multiphase synchronous rectification technology (MSRT) and advanced MPPT control algorithm, with dual-core processor architecture and common negative design, has the features of high response speed, high reliability, and high industrial standard.

MSRT can give a very high conversion efficiency in any charge power, which sharply improves the energy efficiency of solar system;

Advanced MPPT control algorithm minimize the maximum power point loss rate and loss time, to ensure the tracking efficiency, corresponding speed as well as high conversion efficiency under high or low power, so that in any situation, Tracer AN products can rapidly track the maximum power point(MPP) of PV array to obtain the maximum energy of the panel.

The limitation function of the charging power and current, and automatic power reduction function fully ensure the stability when works with oversize PV modules and operate under high temperature environment.

 

 

   VIDEO DEMO

 Latest product information（For more product video please click here） 

DuoRacer Series ——MPPT Dual Battery Solar Charge Controller

DuoRacer MPPT charge controller is made for charging two batteries (shown as BATT1 and BATT2 below) at the same time in a solar system. This controller supports multiple life battery (BATT1) types, including Sealed, Gel, Flooded, LiFePO4, and Li-NiCoMn, which is suitable for RV, Camper, Boat, and so on. The device recognizes the start battery (BATT2) system voltage automatically, and trickle charges the battery when the conditions are satisfied.

The controller adopts the advanced MPPT control algorithm,which will minimize the maximum power point loss rate and loss time,also fast track the maximum power point(MPP) of the PV array, and obtain the maximum energy from solar array under any conditions. The energy utilization in the MPPT solar system is increased by 20-30% compared with PWM charging method. When there is no manual operation for a long time, and the charging conditions cannot be reached, the controller will turn to low-power mode, which reduces the loss and battery power waste to enhance the products life. The system parameters are shown and set by LED/LCD or the MT11 remote meter (Accessory).

The AES control signal of the car refrigerator is built in the controller, which will supply the surplus solar power to the refrigerator to avoid energy waste. The controller comes with IP33 protection level, which is waterproof and dustproof. Multiple protection features, including battery overcharge protection, over discharge protection, and reverse connection protection of the PV and battery, which effectively ensure the solar system safety, stability, and lifetime.

Features

· Maximum Power Point Tracking technology with ultra-fast tracking speed and the  tracking efficiency is no less than 99.5% guaranteed

· Advanced MPPT control algorithm to minimize the MPPlost rate and lost time

· The wider range of the MPP operation voltage to improve the PV module
   utilization

· Auto control function of charging power & charging current limitation(BATT1)

· High quality and low failure rate components of ST, TI and Infineon to ensure      the    product life

· Digital circuit control of adaptive three-stage charging mode to enhance BATT1
   life.

· BATT1 type can be set via LED/LCD.

· Product runs into the low-power mode when there is no manual operation for a
  long time, and charging conditions are not satisfied (PV<5V).
· 100% charging and discharging in operationenvironmental temperature range.

· LED and LCD dispiay units selectable.

· AES control signal for car refrigerator to avoid energy waste.

· Standard Modbus protocol, and RS485 (5V/200mA) communication port for  the  customer to expand the application area.

Technical specifications

 Mechanical Parameters

 Environmental Parameters

①The Temperature compensate coefficient is zero and not changeable when the life battery type is lithium battery。

②If the AES signal port and RS485 communication port are used in the same time, the toal current is no greater than 200mA.

③The communication baud rate can only be set via PC software.

④The LCD backing time can only be set via PC software, setting range is 0~999S and the 0s means the LCD is on all the time. DDB:DuoRacer Display Basic (LED) DDS:DuoRacer Display Standard (LCD)

 VIDEO DEMO

For more product video please click here

Feature:

Compatible with PC software & MT50 for real-time monitoring
Connect to PC via USB interfaces with high compatibility
Powered up by controller communication interface
Record capacity: 20000 points(MAX)
LED Indicator design, more intuitive display

technical parameter