SolarEpic

SolarEpic33 Products

Category
  • Accessories&Tools (7)
  • Feature Products (10)
  • Grid tie inverter (8)
  • MC4 Connectors (3)
  • MPPT Solar Charger Controller (9)
  • Off Grid Inverter (0)
  • PWM Solar Charger Controller (1)
  • Waterproof Grid tie inverter (0)
$109.00

DuoRacer Series ——MPPT Dual Battery Solar Charge Controller

DuoRacer MPPT charge controller is made for charging two batteries (shown as BATT1 and BATT2 below) at the same time in a solar system. This controller supports multiple life battery (BATT1) types, including Sealed, Gel, Flooded, LiFePO4, and Li-NiCoMn, which is suitable for RV, Camper, Boat, and so on. The device recognizes the start battery (BATT2) system voltage automatically, and trickle charges the battery when the conditions are satisfied.

The controller adopts the advanced MPPT control algorithm,which will minimize the maximum power point loss rate and loss time,also fast track the maximum power point(MPP) of the PV array, and obtain the maximum energy from solar array under any conditions. The energy utilization in the MPPT solar system is increased by 20-30% compared with PWM charging method. When there is no manual operation for a long time, and the charging conditions cannot be reached, the controller will turn to low-power mode, which reduces the loss and battery power waste to enhance the products life. The system parameters are shown and set by LED/LCD or the MT11 remote meter (Accessory).

The AES control signal of the car refrigerator is built in the controller, which will supply the surplus solar power to the refrigerator to avoid energy waste. The controller comes with IP33 protection level, which is waterproof and dustproof. Multiple protection features, including battery overcharge protection, over discharge protection, and reverse connection protection of the PV and battery, which effectively ensure the solar system safety, stability, and lifetime.

 

 

Features

· Maximum Power Point Tracking technology with ultra-fast tracking speed and the  tracking efficiency is no less than 99.5% guaranteed


· Advanced MPPT control algorithm to minimize the MPPlost rate and lost time


· The wider range of the MPP operation voltage to improve the PV module
   utilization


· Auto control function of charging power & charging current limitation(BATT1)


· High quality and low failure rate components of ST, TI and Infineon to ensure      the    product life


· Digital circuit control of adaptive three-stage charging mode to enhance BATT1
   life.


· BATT1 type can be set via LED/LCD.


· Product runs into the low-power mode when there is no manual operation for a
  long time, and charging conditions are not satisfied (PV<5V).
· 100% charging and discharging in operationenvironmental temperature range.


· LED and LCD dispiay units selectable.


· AES control signal for car refrigerator to avoid energy waste.


· Standard Modbus protocol, and RS485 (5V/200mA) communication port for  the  customer to expand the application area.

 

 

Technical specifications

Item

     DR1206N-DDB      DR1206N-DDS

DR2210N-DDB DR2210N-DDS

DR3210N-DDB DR3210N-DDS

BATT1 rated voltage

12/24VDC

Rated Charge Current

10A

20A

30A

Battery Input Voltage Range

8.5~32V

Max. PV Open Circuit Voltage

60V(At min. operating environment temp.) 46V(At 25℃ environment temp.)

100V(At min. operating environment temp.) 92V(At 25℃ environment temp.)

MPP Voltage Range

(Battery Voltage+2V)~36V

(Battery Voltage+2V)~72V

Rated Charge Power

130W/12V

260W/24V

260W/12V 520W/24V

390W/12V 780W/24V

Max. conversion efficiency

97.40%

97.50%

98%

Full load efficiency

97%

96%

96%

Self-consumption

12mA/12V;8mA/24V 4mA/12V;3mA/24V(Low-power mode)

26mA/12V;15mA/24V 19mA/12V;10mA/24V(Low-power mode)

Temperature compensate coefficient①

-3mV/℃/2V(default)

Grounding

Common negative

Common negative

13.8V/12V;27.6V/24V(default)

BATT2 Charge return voltage

13V/12V;26V/24V(defaul

AES signal port ②

5VDC/Max.200mA(3.81-4P)

RS485 com. port ②

Com. baud rate③

115200(default)

LCD backlight time④

60S(default)

 Mechanical Parameters

 

Item

DR1206N-DDB DR1206N-DDS

DR2210N-DDB DR2210N-DDS

DR3210N-DDB DR3210N-DDS

Dimension

227.2×143×58.1mm

243.7×158×63mm

247.2×165×68.5mm

Mounting dimension

160×134mm

180×149mm

180×156mm

Mounting hole size

φ5mm

Terminal

12AWG/4mm2 (BATT1) 12AWG/4mm²(BATT2)

6AWG/16mm2 (BATT1)

12AWG/4mm²(BATT2)

Recommended cable size

12AWG/4mm²(BATT1) 12AWG/4mm²(BATT2)

10AWG/6mm²(BATT1) 12AWG/4mm²(BATT2)

8AWG/6mm²(BATT1) 12AWG/4mm²(BATT2)

Weight

0.8kg

1.1kg

1.4kg

 

 Environmental Parameters

 

Item

DR1206/2210N-DDB DR1206/2210N-DDS

  DR3210N-DDB   DR3210N-DDS

Working environment temperature(100% input and output)

﹣20℃~+50℃(DDS)

﹣30℃~+50℃(DDB

﹣20℃~+45℃(DDS)

﹣30℃~+45℃(DDB)

Storage temperature range

-30℃~+80℃

Relative humidity

≤95%, N.C

Enclosure

IP33 3-protection against solid objects: protected against solids objects over 2.5mm. 3-protected against sprays to 60°from the vertical.

Pollution degree

PD2

 

①The Temperature compensate coefficient is zero and not changeable when the life battery type is lithium battery。

②If the AES signal port and RS485 communication port are used in the same time, the toal current is no greater than 200mA.

③The communication baud rate can only be set via PC software.

④The LCD backing time can only be set via PC software, setting range is 0~999S and the 0s means the LCD is on all the time. DDB:DuoRacer Display Basic (LED) DDS:DuoRacer Display Standard (LCD)

 

 VIDEO DEMO

GOFor more product video please click here


    -29%
    $20.00 $27.99

    Feature:

    Compatible with PC software & MT50 for real-time monitoring
    Connect to PC via USB interfaces with high compatibility
    Powered up by controller communication interface
    Record capacity: 20000 points(MAX)
    LED Indicator design, more intuitive display

    technical parameter

    Model

    eLOG01

    Input voltage

    410VDC

    Powered up by RS485 interface

    Average power consumption

    0.3W

    Baud rate

    115200

    Communication

    RS485

    Interface type

    2 RJ45

    1 Micro USB

    Record time

    10 minutes

    Dimensions

    71×67.62×25.8mm

    Mounting dimension

    57.6mm

    Mounting hole size

    Φ4.5

    Working temperature

    -2575

    Humidity

    5-95% (N.C.)

    Enclosure

    IP30

    Net weight

    42g

    Warranty

    2 years

     

      Quick look
      $82.96

      IPower series is a pure sine wave inverter which can convert 12/24/48Vdc into 110V/220Vac. It has the characteristics of concise outline, compact size, high reliability, high efficiency, easy to install and operate and so on. The inverter applicable to household emergency lighting system, vehicle mounted system and small field power supply, etc.

      Feature:

      • Safe design with input and output electrical isolation
      • Adoption of advanced SPWM technology, pure sine wave output
      • Optional output voltage220/230VAC (or 110/120VAC ), setted by DIP switch
      • Output frequency 50/60Hz, setted by DIP switch
      • LED indicators for working and fault status
      • Lower No-load consumption
      • Max. efficiency up to 95%
      • Input protection: Over voltage protection, low voltage protection
      • Output protection: Over load protection, short circuit protection
      • Over temperature protection: Temperature-controlled Fan Ventilation; Inverter turns off automatically
      • Industrial grade design
      Technical specifications(350W/500W):
                    Model 350-11 500-11 350-21 500-21 350-12 500-12 350-22 500-22
      Item
      Input Rated Voltage 12VDC 24VDC 12VDC 24VDC
      Input Voltage Range 10.8~16VDC 21.6~32VDC 10.8~16VDC 21.6~32VDC
      Input surge voltage <32V <44V <32V <44V
      Fuse 32VDC/50A 2*32VDC/35A 32VDC/30A 2*32VDC/25A 32VDC/50A 2*32VDC/35A 32VDC/30A 2*32VDC/25A
      No-load current <0.7A <0.9A <0.5A <0.5A <0.7A <0.9A <0.5A <0.5A
      Output Voltage 110VAC(±5%) 220VAC(±5%)
      120VAC(-10%~+5%) 230VAC(-10%~+5%)
      Output Continuous Power(-20℃~+45℃) 350VA 500VA 350VA 500VA 350VA 500VA 350VA 500VA
      Power factor 0.8 0.8
      Instantaneous impact power ≥750VA ≥1000VA ≥750VA ≥1000VA ≥750VA ≥1000VA ≥750VA ≥1000VA
      Output way Single phase Single phase
      Output Wave Pure sine wave Pure sine wave
      Output Frequency 50/60Hz(±0.2%) 50/60Hz(±0.2%)
      Distortion THD THD≤5%(Resistive load) THD≤5%(Resistive load)
      Max. Efficiency 91% 92%
      90%(IP350-11) 91%(IP350-12)
      Max. USB Output 5VDC/1A 5VDC/1A

       

      Model 350-11
      350-12
      350-21
      350-22
      500-11
      500-12
      500-21
      500-22
      DC input terminal 6mm2
      Overall dimension 214×105.5×57.7mm 232.2×132×74.5mm
      Mounting dimension 185.5×76.7mm 205×102mm
      Mounting hole size Φ4.2mm Φ5.2mm
      Net weight 0.9kg 1.4kg
      Working environment temperature -20℃~+45℃
      Storage temperature range -35℃~+70℃
      Humidity range ≤93%(N.C.)
      Enclosure IP20
      Altitude <2000m
      (Derating to operate according to IEC62040 at a height exceeding 1000 m)
      Technical specifications(1500W/2000W):
      Model  1500-11 1500-21 2000-21 2000-41 1500-12 1500-22 2000-22 2000-42
      Item
      Input Rated Voltage 12VDC 24VDC 24VDC 48VDC 12VDC 24VDC 24VDC 48VDC
      Input Voltage Range 10.8~16VDC 21.6~32VDC 21.6~32VDC 43.2~60VDC 10.8~16VDC 21.6~32VDC 21.6~32VDC 43.2~60VDC
      Input surge voltage <20VDC <40VDC <40VDC <80VDC <20VDC <40VDC <40VDC <80VDC
      No-load current <1.0A <0.6A <0.6A <0.4A <1.0A <0.6A <0.6A <0.4A
      Output Voltage 110VAC(±5%) 110VAC(±5%) 220VAC(±5%) 220VAC(±5%)
      120VAC(-7%~+5%) 120VAC(-10%~+5%) 230VAC(-7%~+5%) 230VAC(-10%~+5%)
      Output Continuous Power 1200W 1600W 1200W 1600W
      Output Power 15 min. 1500W 2000W 1500W 2000W
      Instantaneous impact power 2400W 3200W 2400W 3200W
      Output way Single phase Single phase Single phase Single phase
      Output Wave Pure sine wave Pure sine wave Pure sine wave Pure sine wave
      Output Frequency 50/60Hz(±0.2%) 50/60Hz(±0.2%) 50/60Hz(±0.2%) 50/60Hz(±0.2%)
      Distortion THD THD≤5%(Resistive load) THD≤5%(Resistive load) THD≤5%(Resistive load) THD≤5%(Resistive load)
      Max. Efficiency 93% 94% 95% 93% 94% 95%
      Max. USB Output 5VDC/1A 5VDC/1A 5VDC/1A 5VDC/1A
      Binding post Φ10mm Φ10mm Φ10mm Φ10mm

       

      Model  1500-11
      1500-12
      1500-21
      1500-22
      2000-21
      2000-22
      2000-41
      2000-42
      Item
      Overall dimension 326.12×231.5×98.5mm 284.7×231.5×98.5mm 326.12×231.5×98.5mm
      Mounting dimension 208×220mm 163×220mm 208×219.5mm
      Mounting hole size Φ5.5mm Φ5.5mm
      Net weight 3.9kg 4.0kg

       

      Working Temperature -20℃~+45℃
      Storage Temperature -35℃~ +70℃
      Humidity < 95%(N.C.)
      Enclosure IP20
      Altitude < 5000 m (Derating to operate according to IEC62040 at a height exceeding 1000 m)
        $26.96

        Note : just can be use for ANDROID phone,

        CAN'T be use for iPHONE.

        APK Download:Epever(WIFI&BLE)

        Feature:

             eBox-BLE-01
        • Realize wireless monitoring function of solar controller and inverter
        • Support mobile phone APP, plug and play, simple and convenient to set
        • Use high performance, ultra-low power consumption Bluetooth dedicated chip
        • Adopt Bluetooth 4.0 and BLE technology
        • Fast communication, strong anti-interference ability
        • No need of external power supply
        • Communication distance up to 10 m
        • Master reset adapter

        Bluetooth

            eBox-WIFI-01

        •  Realize wireless monitoring function of solar controller and inverter
        • Support mobile phone APP, plug and play, simple and convenient to set
        • Use high performance CPU with core M4
        • Ultra-low power consumption and high speed data processing capability
        • No need of external power supply
        • Communication distance up to 50 m
        • One-key restore the factory settings

        WIFI

         

        Technical Specifications

        Model→

        Item↓

        eBox-BLE-01

        eBox-WIFI-01

        Input Voltage

        5VDC

        (Direct powered by RS485 port )

        5VDC

        (Direct powered by RS485 port )

        Standby power

        Consumption

        0.04W

        0.20W

        Operation power

        consumption

        0.05W

        0.25W

        Communication distance

        ≤10m

        ≤50m

        Port baud rate

        300bps~230400bps (Default115200)

        300bps~230400bps (Default 115200)

        Communication

        RS485 to BLE

        RS485 to WIFI

        Interface type

        RJ45

        RJ45

        Connecting cable

        Standard network cable

        (Parallel cable)

        Standard network cable

        (Parallel cable)

        Overall dimension

        51*67*24.5mm

        51*67*24.5mm

        Mounting dimension

        41.2mm

        41.2mm

        Mounting hole size

        Φ3.2mm

        Φ3.2mm

        Working temperatur

        -20~70℃

        -35~75℃

        Enclosure

        IP30

        IP30

        Net weight

        37g

        39g

          -36%
          $29.39 $45.99

          Feature

            • Ultra-saving pliers. Cold press pliers. Terminal pliers series
            • The new crimping pliers adopts the principle of lever to effectively design the handle.
            • Although the structure is small and compact, it is very labor-saving when operating, especially when crimping the wires with large transverse joint sections.
            • For non-welded, electrical connections that meet the accuracy criteria
            • Precision crimping module and integral locking (custom release mechanism) design ensures high quality crimp line standards during repeated crimping
            • Precise and accurate adjustment before leaving the factory.

           

           

          Model

          H03

          suitable object

          cable

          effect

           

          Break,tighten,strip,press

           

          character

          general

          texture

          chisel tool steel

          style

          German-style

            Quick look
            $133.00

             

            Item specifics

            Condition:
            New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is ... Read more
            Model:

            Waterproof Grid Tie Inverter

            Features: Waterproof Type: Grid Tie Inverter
            Power: 300W MPN:

            WG300110227

            Charging Mode: MPPT (Maximum Power Point Tracking) Brand:

            SolarEpic

            DC Input Voltage: 22-50VDC Application: Home/Garden
            Waterproof Rating: IP65 Resistance Properties: Waterproof
            Certificate: CE Country/Region of Manufacture: China
            Bundle Listing: Yes Current Type: AC/DC
            Featured Refinements: Grid Tie Inverter System Configuration: Grid-Tie
            RMS Power: 300W Material: Waterproof
            Voltage: 24V/36V

             

            Note : This inverter do not have the monitoring function.


            300W waterproof grid tie inverter,pure sine wave inverter.

            DC22V-50V to AC110V or 220V, 50Hz/60Hz auto.

            Waterproof IP65.

            Use for 24v/36v solar panel,do not suggest to use for battery or wind power.


            System Function

            ◆ 6-grade power search---In overcast weather, the PV Panel’s output current is extremely tiny, then inverter will automatic open 6-grade power search function,and keep outputing efficent and steady during the low power .

            ◆ Wide voltage input(22-50VDC)---

            1. DC voltage input:22~50VDC; 2. Second level power variable voltage conversion.

            ◆ High-frequency two-way and one-way grid function---

            1. High frequency direct modulation, AC half wave synthesis;
            2. Two-way grid means: Load consume directly. And can reverse AC current transmission.

            ◆ Kinds of frequency output function---

            1. It can apply to 50Hz and 60Hz frequency of AC; 2. Frequency range: 45Hz ~ 64Hz;

            Directly connected to the solar panels (do not need to connect the battery)

            ◆ AC 0 angle with high precision auto-detection---

            High-precision analysing the AC phase angle .The phase shift rate is less than 1%, thus achieve high-precision with phase modulation AC output together.1. AC phase shift: < 1%; 2. Over-zero protection: 0.2 VAC; 3. AC switching: 50Hz / 60Hz.

            ◆ Synchronous High-frequency Modulation

            1. Modulation synthesis: half wave and full-bridge modulation synthesis (100Hz / 120Hz) ;
            2. Synthetic way: MOSFET full-bridge; 3. High frequency: 50KHz.

            ◆ Pure Sine Wave Output---Use SPWM directly to make pure sine wave output.

            1. Output waveform: Adopt complementary PWM to push-pull pure sine wave;
            2. Generate means: enhancement-mode SPWM.

            ◆ Power Automatically Locked (APL)---

            automatically powers locked in maximum power point, made output more stable.

            ◆ Constant Current, Constant Power---

            constant current and output power, without any overload, over-current phenomenon.

            ◆ Exactly and timely automatic Island Effect Protection

            ◆ High-Frequency High Conversion Rate---

            Adapt high frequency converter, the output more efficient.

            ◆ Maximum Power Point Tracking (MPPT)---

            high-precision (MPPT) operation power, automatic and immediate adjust the solar panels output power at the maximum output point,made the inverter discharge to power grid with the highest efficiency.

            ◆ Stack using--- Such as: 4 micro inverter of 260W stacking can achieve 1040W. the number of the stacking is unlimited.

            ◆ DC input---Input voltage range: 22V to 50V,PV Panel: Recommend using the power more than 30W and the standard voltage of 36V PV panels.Suggestion making the PV in parallel.

            ◆ AC output---220VAC: 180V - 262V, 50HZ; 110V AC: 80V - 160V,60HZ.


            Notes:

            ★Please connect the inverter following the operation instruction show above. If have any question please contact with relative persons.

            ★Non-professionals do not disassemble.Only qualified personnel may repair this product.

            ★Please install inverter in the low humidity and well ventilated place to avoid the inverter over-heating,and clear around the inflammable and explosive materials.

            ★When using this product, avoid children touching,playing, to avoid electric shock.

            ★Connected solar panels, battery or wind generators DC input DC power supply cable.

             

            LED Display:

            1.Red light 3 second---Red LED light 3 second while device starts , then in working condition;

            2.Green flash fast---MPPT searching;

            3.Green flash slow---MPPT + searching;

            1. Red flash slow---MPPT - searching;

            5.Green lights on 3s and off 0.5s---MPPT locked;

            6.Red light steady---

            1. Islanding protection;

            b.Over-temperature protection;

            c.Over / low AC voltage protection;

            1. Over / low DC voltage protection; e.Fault

             

            Remarks 

            LED flashing in the process of being working condition : inverters connected to AC & DC sides→Red LED light 3 second→Green LED flash fast(MPPT searching)→Green LED flash slow(MPPT + searching) / Red LED flash slow (MPPT - searching) / reen LED lights on 3s and off 0.5s (MPPT locked) .

             

            Package

            1.One user manual;

            2.One 300W inverter;

            3.One AC Cable;

              $156.00

               

              Item specifics

              Condition:
              New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is ... Read more
              Model:

              Waterproof Grid Tie Inverter

              Power: 600W Type: Grid Tie Inverter
              Charging Mode: MPPT (Maximum Power Point Tracking) MPN:

              WG60010016

              DC Input Voltage: 22V-50VDC Brand:

              SolarEpic

              Waterproof Rating: IP65 Application: Home/Garden
              Certificate: CE Resistance Properties: Waterproof
              Energy Type: Solar Country/Region of Manufacture: China
              Bundle Listing: Yes Current Type: AC/DC
              Featured Refinements: Grid Tie Inverter System Configuration: Grid-Tie
              Voltage: 24V

               

              Note : This inverter do not have the monitoring function.


              600W waterproof grid tie inverter,pure sine wave inverter.

              DC20V-50V to AC110V or 220V,50Hz/60Hz auto.

              Waterproof IP65.



              System Function

               Wireless communication 433/462MHz

               6-grade power search---In overcast weather, the PV Panel’s output current is extremely tiny, then inverter will automatic open 6-grade power search function,and keep outputing efficent and steady during the low power .

               Wide voltage input(22-50VDC)---

              1. DC voltage input:22~50VDC; 2. Second level power variable voltage conversion.

               High-frequency two-way and one-way grid function---

              1. High frequency direct modulation, AC half wave synthesis;
              2. Two-way grid means: Load consume directly. And can reverse AC current transmission.

               Kinds of frequency output function---

              1. It can apply to 50Hz and 60Hz frequency of AC; 2. Frequency range: 45Hz ~ 64Hz;

              Directly connected to the solar panels (do not need to connect the battery)

               AC 0 angle with high precision auto-detection---

              High-precision analysing the AC phase angle .The phase shift rate is less than 1%, thus achieve high-precision with phase modulation AC output together.1. AC phase shift: < 1%; 2. Over-zero protection: 0.2 VAC; 3. AC switching: 50Hz / 60Hz.

               Synchronous High-frequency Modulation

              1. Modulation synthesis: half wave and full-bridge modulation synthesis (100Hz / 120Hz) ;
              2. Synthetic way: MOSFET full-bridge; 3. High frequency: 50KHz.

               Pure Sine Wave Output---Use SPWM directly to make pure sine wave output.

              1. Output waveform: Adopt complementary PWM to push-pull pure sine wave;
              2. Generate means: enhancement-mode SPWM.

               Power Automatically Locked (APL)---

              automatically powers locked in maximum power point, made output more stable.

               Constant Current, Constant Power---

              constant current and output power, without any overload, over-current phenomenon.

               Exactly and timely automatic Island Effect Protection

               High-Frequency High Conversion Rate---

              Adapt high frequency converter, the output more efficient.

               Maximum Power Point Tracking (MPPT)---

              high-precision (MPPT) operation power, automatic and immediate adjust the solar panels output power at the maximum output point,made the inverter discharge to power grid with the highest efficiency.

               Stack using--- Such as: 4 micro inverter of 260W stacking can achieve 1040W. the number of the stacking is unlimited.

               DC input---Input voltage range: 22V to 50V,PV Panel: Recommend using the power more than 30W and the standard voltage of 36V PV panels.Suggestion making the PV in parallel.

               AC output---220VAC: 180V - 262V, 50HZ; 110V AC: 80V - 160V,60HZ.


              Notes:

              ★Please connect the inverter following the operation instruction show above. If have any question please contact with relative persons.

              ★Non-professionals do not disassemble.Only qualified personnel may repair this product.

              ★Please install inverter in the low humidity and well ventilated place to avoid the inverter over-heating,and clear around the inflammable and explosive materials.

              ★When using this product, avoid children touching,playing, to avoid electric shock.

              ★Connected solar panels, battery or wind generators DC input DC power supply cable.

               

              LED Display:

              1.Red light 3 second---Red LED light 3 second while device starts , then in working condition;

              2.Green flash fast---MPPT searching;

              3.Green flash slow---MPPT + searching;

              1. Red flash slow---MPPT - searching;

              5.Green lights on 3s and off 0.5s---MPPT locked;

              6.Red light steady---

              1. Islanding protection;

              b.Over-temperature protection;

              c.Over / low AC voltage protection;

              1. Over / low DC voltage protection; e.Fault

               

              Remarks

              LED flashing in the process of being working condition : inverters connected to AC & DC sides→Red LED light 3 second→Green LED flash fast(MPPT searching)→Green LED flash slow(MPPT + searching) / Red LED flash slow (MPPT - searching) / reen LED lights on 3s and off 0.5s (MPPT locked) .

               

               
              What's In Box

              1.One user manual;

              2.One 600W inverter;

              3.One AC Cable;

                $35.00

                The MT series remote meter is an accessory which is compatible with the DuoRacer series controller. It can monitor the running data and working status of the controller via the remote meter. The remote meter can browse the controller’s parameters, set the battery typeand temperature unit, and clean the generated energy.It is suitable for RV, Camper, Boat, and so on.

                Recommendations

                • The MT11 is only allowed to connect with DR N series charge controller.Please confirm before purchase and installation.
                • Pleasedo not install MT11 in a situation with strong electromagnetic 

                Features

                • Automatically identify and display the type,model and relevant parameterdata of controllers.
                • Real-timedisplay the operational data and working status of the connected devices indigital,graphics and textual forms by a large-screen multifunction LCD.
                • Three touch buttons are easy and quick to operate.
                • No need for external power supply. Charge controller supply the power for MT11.
                • It can browse the controller’s parameters, set the battery typeand temperatureunit, and clean the generated energy.
                • Real-time display of failure information of the connecteddevices.
                • Longer communication distance based on RS485.
                Technical Specifications        

                Model

                MT11

                Apply to model

                DRN series

                Self-consumption(Power on)

                13mA/5Vdc

                Self-consumption(Power off)

                4mA

                Communication way

                RS485

                Communication port

                3.81-4P

                RS485 cable

                CC-RS485-RS485-3.81-4P-150(1.5m)

                CC-RS485-RS485-3.81-4P-500(5m)

                CC-RS485-RS485-3.81-4P-1000(10m)

                Environment temperature

                -20℃~+70℃

                Storage temperature range

                -20℃~+70℃

                Enclosure

                IP20

                Dimension

                98.4×98.4mm

                Base cover dimension

                114×114mm

                Weight

                0.11kg


                Front View


                 

                LCD display screen

                Man-machine interaction operation interface. 

                Buttons

                The meter buttons include two function buttons and one switch button.

                 

                Press the button

                1.PV array parameters

                2.Storage battery parameters

                3.Browse the start battery parameters automatically ()

                 

                Press the button

                Browse the PV array parameters

                Browse the Storage battery parameters

                Browse the start battery parameters

                Press the button and hold on 5s

                Temperature unitsBattery type

                 

                Press the button

                The meter is powered ON

                Press the button and hold on 5s

                The meter is powered OFF

                 

                 Rear View

                 

                 

                • RS485communicationport

                It is used to connect the controller which Power the MT11.

                • Communicationcables models

                CC-RS485-RS485-3.81-4P-150(Included)

                CC-RS485-RS485-3.81-4P-1000(Optional)

                CC-RS485-RS485-3.81-4P-2000(Optional)

                 

                • Pins definition

                PIN

                Definition

                1

                DC5V

                2

                RS-485-B

                3

                RS-485-A

                4

                GND

                 

                 

                LCD display

                 

                Icon

                Instruction

                Icon

                Instruction

                 

                BATT1 battery capacity level0~12%

                 

                BATT2battery capacity level0~12%

                 

                BATT1battery capacity level13%~35%

                 

                BATT2battery capacity level13%~35%

                 

                BATT1battery容量水平 36%〜61%

                 

                BATT2battery capacity level36%~61%

                 

                BATT1battery capacity level62%~86%

                 

                BATT2battery capacity level62%~86%

                 

                BATT1battery capacity level

                87%~100%

                 

                BATT2battery capacity level

                87%~100%

                 

                Day

                 

                PV array

                Night

                 

                BATT1 charging icon

                 

                Display the parameters of PV

                 

                BATT2charging icon

                 

                Display the parameters of BATT1

                 

                BATT1temperature parameters

                 

                Display the parameters of BATT2

                 

                AES signal icon

                 

                Setting icon

                 

                Battery type icon

                 

                Auto global view sign

                 

                Minimum voltage icon

                 

                Fault Icon

                 

                Maximum voltage icon

                Battery power capacity is calculated by the linear relationship between the disconnect voltage of low voltage and float charging voltage.

                  Quick look

                  Search

                  Just added to your cart:
                  Qty:
                  Total:
                  Subtotal:
                  Excl. postage 
                  My Bag
                  Just added to your wishlist:
                  Excl. postage 
                  My Wishlist

                  Join Our Mailing List

                  Spin to win Spinner icon